Steel end bracket set completes both chian ends and allow for fastening on outer radius and inner radius: mounting position must be specified. Stainless steel can be delivered on request.
For correct functioning of the chain it is necessary that the installation is done in a specific position. For this reason Brevetti Stendalto has observed and created a support guide which can do this. For particular applications it is possible to create support guides with attachment plates and special dimensions. For applications with rotations exceeding 200° it is necessary to use the appropriate accessories for supporting the cable chain.
Norms | Properties | Units | Dry | Conditioned |
---|---|---|---|---|
TERMICHE | ||||
DSC | Melting point (10° C/min.) | °C | ||
ASTM - D 696 | Coefficient of linear thermal expansion | X10-6 K-1 | ||
ASTM D 648 ISO 75 DIN 53461 |
Heat distortion temperature ISO 75 1.82 N/mm2 °C 210 DIN 53461 0.45 N/mm2 |
°C °C |
210 220 |
|
U. L. 94 | Flammability | H.B. | ||
IEC 695-2-1 | Incandescent wire Temperature °C 650 Thickness |
650 3 |
||
FLAMMABILITY | ||||
ASTM-D 257 | Volume resistivity | Ohm cm | 1015 | 1011 |
ASTM-D 257 | Surface resistivity | Ohm | 1013 | 1011 |
ASTM-D 149 | Dielectric strength | KV/mm | 22 | |
ASTM-D 150 | Dielectric constant (10 Hz) | - | 3.8 | 4.5 |
ASTM-D 150 | Dissipation factor (10Hz) | - | 0.02 | 0.09 |
PHYSICAL PROPERTIES |
||||
ASTM-D 792 | Density | g/cm3 | 1.38 | |
ASTM-D 570 | Water absorption at 23°C in water for 24 hours | % | 0.90 | |
MECHANICAL PROPERTIES | ||||
ASTM-D 638 ISO R/527 DIN 53455 |
Tensile yield stress Ultimate elongation |
N/mm2 % |
195 2.6 |
115 4 |
ASTM-D 638 ISO R/527 DIN 53457 |
Tensile modulus of elasticity | N/mm2 | 10600 | 6900 |
ASTM-D 790 ISO 178 DIN 53452 |
Flexural strength | N/mm2 | 310 | 190 |
ASTM-D 790 ISO 178 |
Flexural modulus | N/mm2 | 10500 | 6800 |
ASTM-D 256 | Unnotched Izod impact strength | J/m | 140 | 300 |
ISO 180/4C | Notched Izod impact strength | KJ/m2 | 110 | 125 |
ASTM-D 785 | Rockwell hardness | Scala R | 122 | 114 |
BRYLON 6 | BRYLON 6 | STEEL | ||
---|---|---|---|---|
Chemical agents | Concentration % | Amorphous | Crystal | |
Methyl acetate | 100 | RB3 | RB2 | RB |
Acetone | 100 | RB4 | RB | RB |
Acetic acid (aqueous solution) | 40 | AF | AF | AF |
Acetic acid (aqueous solution) | 10 | AF | AF | AF |
Acetic acid | AF | AF | AF | |
Citric acid | 10 | AD 15 | RD | AD |
Hydrochloric acid (aqueous solution) | 36 | S | S | S |
Hydrochloric acid (aqueous solution) | 10 | AF | AF | S |
Hydrochloric acid (aqueous solution) | 2 | AF | AD | S |
Chromic acid (aqueous solution) | 10 | AF | AF | AF |
Chromic acid (aqueous solution) | 1 | RD | RD | AF |
Hydrofluoric acid | 40 | AF | AF | S |
Formic acid (aqueous solution) | 85 S | S | AD | |
Formic acid (aqueous solution) | 40 S | AF | AF | AD |
Phosphoric acid (aqueous solution) | 10 | AF | AF | S |
Oleic acid | 100 | RB3 | RB3 | RD |
Sulphuric acid | 98 | S | S | S |
Sulphuric acid (aqueous solution) | 40 | AF | AF | S |
Sulphuric acid (aqueous solution) | 10 | AF | AF | S |
Sulphuric acid (aqueous solution) | 2 | AF | AD | S |
Tartaric acid (aqueous solution) | RD | RB | RD | |
Water | RB10 | RB9 | RD | |
Chlorine water | RD | RD | AD | |
Ethyl alcohol | 96 | RD17 | RB3 | RB |
Ammonia | 10 | RB11 | RB | AF |
Petrol | 100 | RB1 | RB | RB |
Bitumen | RD | RD | RB | |
Potassium carbonate | 100 | RB | RB | AF |
Sodium carbonate | 10 | RB10 | RB3 | AF |
Ammonium chloride (aqueous solution) | 10 | RB | RB | AF |
Calcium chloride (aqueous solution) | 20 | S | S | AF |
Calcium chloride (aqueous solution) | 10 | RB | RB | AF |
Sodium chloride | 10 | RB | RB | AF |
Formaldehyde (aqueous solution) | 30 | RD | RB | AD |
Fat | RB | RB | RB | |
Milk | RB | RB | RB | |
Mercury | RB | RB | RB | |
Oils | RB | RB | RB | |
Oil | RB | RB | RB | |
Paraffin oil | RB | RB | RB | |
Silicon oil | RB | RB | RB | |
Diesel oil | RB | RB | RB | |
Mineral oil | RB | RB | RB | |
Ozone | AF | AF | AF | |
Oil | RB | RB | RB | |
Potassium hydroxide (aqueous solution) | 10 | RB9 | RB3 | S |
Sodium hydroxide (aqueous solution) | 50 | RD | RD | S |
Sodium hydroxide (aqueous solution) | 10 | RB5 | RB | S |
Sodium hydroxide (aqueous solution) | 5 | RB9 | RB | S |
Aluminium sulphate | 10 | RB | RB | AF |
Soap (aqueous solution) | RB | RB | RB | |
Tincture of iodine | AF | AF | AD | |
Trichloroethylene | RD5 | RD4 | RB | |
Vaseline | RB | RB | RB |
Legend
The table shows the resistance to chemical agents of BRYLON 6 and Steel. The number by resistance value side shows which is the % weight increase due to swelling.
RB - Very good resistance.
RD - Good resistance.
AD - Limited resistance.
AF - Poor resistance.
S - Soluble.
Amorphous - Polymer in amorphous state.
Crystal - Polymer in crystalline state.
Temperature range: -30°C + 125°C